1 /* USER CODE BEGIN Header */ 2 /** 3 ****************************************************************************** 4 * @file stm32f1xx_hal_conf.h 5 * @brief HAL configuration file. 6 ****************************************************************************** 7 * @attention 8 * 9 * Copyright (c) 2017 STMicroelectronics. 10 * All rights reserved. 11 * 12 * This software is licensed under terms that can be found in the LICENSE file 13 * in the root directory of this software component. 14 * If no LICENSE file comes with this software, it is provided AS-IS. 15 * 16 ****************************************************************************** 17 */ 18 /* USER CODE END Header */ 19 20 /* Define to prevent recursive inclusion -------------------------------------*/ 21 #ifndef __STM32F1xx_HAL_CONF_H 22 #define __STM32F1xx_HAL_CONF_H 23 24 #ifdef __cplusplus 25 extern "C" { 26 #endif 27 28 /* Exported types ------------------------------------------------------------*/ 29 /* Exported constants --------------------------------------------------------*/ 30 31 /* ########################## Module Selection ############################## */ 32 /** 33 * @brief This is the list of modules to be used in the HAL driver 34 */ 35 36 #define HAL_MODULE_ENABLED 37 /*#define HAL_ADC_MODULE_ENABLED */ 38 /*#define HAL_CRYP_MODULE_ENABLED */ 39 /*#define HAL_CAN_MODULE_ENABLED */ 40 /*#define HAL_CAN_LEGACY_MODULE_ENABLED */ 41 /*#define HAL_CEC_MODULE_ENABLED */ 42 /*#define HAL_CORTEX_MODULE_ENABLED */ 43 /*#define HAL_CRC_MODULE_ENABLED */ 44 /*#define HAL_DAC_MODULE_ENABLED */ 45 /*#define HAL_DMA_MODULE_ENABLED */ 46 /*#define HAL_ETH_MODULE_ENABLED */ 47 /*#define HAL_FLASH_MODULE_ENABLED */ 48 #define HAL_GPIO_MODULE_ENABLED 49 /*#define HAL_I2C_MODULE_ENABLED */ 50 /*#define HAL_I2S_MODULE_ENABLED */ 51 /*#define HAL_IRDA_MODULE_ENABLED */ 52 /*#define HAL_IWDG_MODULE_ENABLED */ 53 /*#define HAL_NOR_MODULE_ENABLED */ 54 /*#define HAL_NAND_MODULE_ENABLED */ 55 /*#define HAL_PCCARD_MODULE_ENABLED */ 56 /*#define HAL_PCD_MODULE_ENABLED */ 57 /*#define HAL_HCD_MODULE_ENABLED */ 58 /*#define HAL_PWR_MODULE_ENABLED */ 59 /*#define HAL_RCC_MODULE_ENABLED */ 60 /*#define HAL_RTC_MODULE_ENABLED */ 61 /*#define HAL_SD_MODULE_ENABLED */ 62 /*#define HAL_MMC_MODULE_ENABLED */ 63 /*#define HAL_SDRAM_MODULE_ENABLED */ 64 /*#define HAL_SMARTCARD_MODULE_ENABLED */ 65 /*#define HAL_SPI_MODULE_ENABLED */ 66 /*#define HAL_SRAM_MODULE_ENABLED */ 67 /*#define HAL_TIM_MODULE_ENABLED */ 68 #define HAL_UART_MODULE_ENABLED 69 /*#define HAL_USART_MODULE_ENABLED */ 70 /*#define HAL_WWDG_MODULE_ENABLED */ 71 72 #define HAL_CORTEX_MODULE_ENABLED 73 #define HAL_DMA_MODULE_ENABLED 74 #define HAL_FLASH_MODULE_ENABLED 75 #define HAL_EXTI_MODULE_ENABLED 76 #define HAL_GPIO_MODULE_ENABLED 77 #define HAL_PWR_MODULE_ENABLED 78 #define HAL_RCC_MODULE_ENABLED 79 80 /* ########################## Oscillator Values adaptation ####################*/ 81 /** 82 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 83 * This value is used by the RCC HAL module to compute the system frequency 84 * (when HSE is used as system clock source, directly or through the PLL). 85 */ 86 #if !defined (HSE_VALUE) 87 #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ 88 #endif /* HSE_VALUE */ 89 90 #if !defined (HSE_STARTUP_TIMEOUT) 91 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 92 #endif /* HSE_STARTUP_TIMEOUT */ 93 94 /** 95 * @brief Internal High Speed oscillator (HSI) value. 96 * This value is used by the RCC HAL module to compute the system frequency 97 * (when HSI is used as system clock source, directly or through the PLL). 98 */ 99 #if !defined (HSI_VALUE) 100 #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz*/ 101 #endif /* HSI_VALUE */ 102 103 /** 104 * @brief Internal Low Speed oscillator (LSI) value. 105 */ 106 #if !defined (LSI_VALUE) 107 #define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */ 108 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 109 The real value may vary depending on the variations 110 in voltage and temperature. */ 111 112 /** 113 * @brief External Low Speed oscillator (LSE) value. 114 * This value is used by the UART, RTC HAL module to compute the system frequency 115 */ 116 #if !defined (LSE_VALUE) 117 #define LSE_VALUE 32768U /*!< Value of the External oscillator in Hz*/ 118 #endif /* LSE_VALUE */ 119 120 #if !defined (LSE_STARTUP_TIMEOUT) 121 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 122 #endif /* LSE_STARTUP_TIMEOUT */ 123 124 /* Tip: To avoid modifying this file each time you need to use different HSE, 125 === you can define the HSE value in your toolchain compiler preprocessor. */ 126 127 /* ########################### System Configuration ######################### */ 128 /** 129 * @brief This is the HAL system configuration section 130 */ 131 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 132 #define TICK_INT_PRIORITY 0U /*!< tick interrupt priority (lowest by default) */ 133 #define USE_RTOS 0U 134 #define PREFETCH_ENABLE 1U 135 136 #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ 137 #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ 138 #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ 139 #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ 140 #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ 141 #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ 142 #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ 143 #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ 144 #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ 145 #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ 146 #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ 147 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ 148 #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ 149 #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ 150 #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ 151 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ 152 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ 153 #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ 154 #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ 155 #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ 156 #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ 157 #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ 158 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ 159 160 /* ########################## Assert Selection ############################## */ 161 /** 162 * @brief Uncomment the line below to expanse the "assert_param" macro in the 163 * HAL drivers code 164 */ 165 /* #define USE_FULL_ASSERT 1U */ 166 167 /* ################## Ethernet peripheral configuration ##################### */ 168 169 /* Section 1 : Ethernet peripheral configuration */ 170 171 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 172 #define MAC_ADDR0 2U 173 #define MAC_ADDR1 0U 174 #define MAC_ADDR2 0U 175 #define MAC_ADDR3 0U 176 #define MAC_ADDR4 0U 177 #define MAC_ADDR5 0U 178 179 /* Definition of the Ethernet driver buffers size and count */ 180 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 181 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 182 #define ETH_RXBUFNB 8U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 183 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 184 185 /* Section 2: PHY configuration section */ 186 187 /* DP83848_PHY_ADDRESS Address*/ 188 #define DP83848_PHY_ADDRESS 0x01U 189 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 190 #define PHY_RESET_DELAY 0x000000FFU 191 /* PHY Configuration delay */ 192 #define PHY_CONFIG_DELAY 0x00000FFFU 193 194 #define PHY_READ_TO 0x0000FFFFU 195 #define PHY_WRITE_TO 0x0000FFFFU 196 197 /* Section 3: Common PHY Registers */ 198 199 #define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ 200 #define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ 201 202 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 203 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 204 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 205 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 206 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 207 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 208 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 209 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 210 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 211 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 212 213 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 214 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 215 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 216 217 /* Section 4: Extended PHY Registers */ 218 #define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ 219 220 #define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ 221 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ 222 223 /* ################## SPI peripheral configuration ########################## */ 224 225 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 226 * Activated: CRC code is present inside driver 227 * Deactivated: CRC code cleaned from driver 228 */ 229 230 #define USE_SPI_CRC 0U 231 232 /* Includes ------------------------------------------------------------------*/ 233 /** 234 * @brief Include module's header file 235 */ 236 237 #ifdef HAL_RCC_MODULE_ENABLED 238 #include "stm32f1xx_hal_rcc.h" 239 #endif /* HAL_RCC_MODULE_ENABLED */ 240 241 #ifdef HAL_GPIO_MODULE_ENABLED 242 #include "stm32f1xx_hal_gpio.h" 243 #endif /* HAL_GPIO_MODULE_ENABLED */ 244 245 #ifdef HAL_EXTI_MODULE_ENABLED 246 #include "stm32f1xx_hal_exti.h" 247 #endif /* HAL_EXTI_MODULE_ENABLED */ 248 249 #ifdef HAL_DMA_MODULE_ENABLED 250 #include "stm32f1xx_hal_dma.h" 251 #endif /* HAL_DMA_MODULE_ENABLED */ 252 253 #ifdef HAL_ETH_MODULE_ENABLED 254 #include "stm32f1xx_hal_eth.h" 255 #endif /* HAL_ETH_MODULE_ENABLED */ 256 257 #ifdef HAL_CAN_MODULE_ENABLED 258 #include "stm32f1xx_hal_can.h" 259 #endif /* HAL_CAN_MODULE_ENABLED */ 260 261 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 262 #include "Legacy/stm32f1xx_hal_can_legacy.h" 263 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 264 265 #ifdef HAL_CEC_MODULE_ENABLED 266 #include "stm32f1xx_hal_cec.h" 267 #endif /* HAL_CEC_MODULE_ENABLED */ 268 269 #ifdef HAL_CORTEX_MODULE_ENABLED 270 #include "stm32f1xx_hal_cortex.h" 271 #endif /* HAL_CORTEX_MODULE_ENABLED */ 272 273 #ifdef HAL_ADC_MODULE_ENABLED 274 #include "stm32f1xx_hal_adc.h" 275 #endif /* HAL_ADC_MODULE_ENABLED */ 276 277 #ifdef HAL_CRC_MODULE_ENABLED 278 #include "stm32f1xx_hal_crc.h" 279 #endif /* HAL_CRC_MODULE_ENABLED */ 280 281 #ifdef HAL_DAC_MODULE_ENABLED 282 #include "stm32f1xx_hal_dac.h" 283 #endif /* HAL_DAC_MODULE_ENABLED */ 284 285 #ifdef HAL_FLASH_MODULE_ENABLED 286 #include "stm32f1xx_hal_flash.h" 287 #endif /* HAL_FLASH_MODULE_ENABLED */ 288 289 #ifdef HAL_SRAM_MODULE_ENABLED 290 #include "stm32f1xx_hal_sram.h" 291 #endif /* HAL_SRAM_MODULE_ENABLED */ 292 293 #ifdef HAL_NOR_MODULE_ENABLED 294 #include "stm32f1xx_hal_nor.h" 295 #endif /* HAL_NOR_MODULE_ENABLED */ 296 297 #ifdef HAL_I2C_MODULE_ENABLED 298 #include "stm32f1xx_hal_i2c.h" 299 #endif /* HAL_I2C_MODULE_ENABLED */ 300 301 #ifdef HAL_I2S_MODULE_ENABLED 302 #include "stm32f1xx_hal_i2s.h" 303 #endif /* HAL_I2S_MODULE_ENABLED */ 304 305 #ifdef HAL_IWDG_MODULE_ENABLED 306 #include "stm32f1xx_hal_iwdg.h" 307 #endif /* HAL_IWDG_MODULE_ENABLED */ 308 309 #ifdef HAL_PWR_MODULE_ENABLED 310 #include "stm32f1xx_hal_pwr.h" 311 #endif /* HAL_PWR_MODULE_ENABLED */ 312 313 #ifdef HAL_RTC_MODULE_ENABLED 314 #include "stm32f1xx_hal_rtc.h" 315 #endif /* HAL_RTC_MODULE_ENABLED */ 316 317 #ifdef HAL_PCCARD_MODULE_ENABLED 318 #include "stm32f1xx_hal_pccard.h" 319 #endif /* HAL_PCCARD_MODULE_ENABLED */ 320 321 #ifdef HAL_SD_MODULE_ENABLED 322 #include "stm32f1xx_hal_sd.h" 323 #endif /* HAL_SD_MODULE_ENABLED */ 324 325 #ifdef HAL_NAND_MODULE_ENABLED 326 #include "stm32f1xx_hal_nand.h" 327 #endif /* HAL_NAND_MODULE_ENABLED */ 328 329 #ifdef HAL_SPI_MODULE_ENABLED 330 #include "stm32f1xx_hal_spi.h" 331 #endif /* HAL_SPI_MODULE_ENABLED */ 332 333 #ifdef HAL_TIM_MODULE_ENABLED 334 #include "stm32f1xx_hal_tim.h" 335 #endif /* HAL_TIM_MODULE_ENABLED */ 336 337 #ifdef HAL_UART_MODULE_ENABLED 338 #include "stm32f1xx_hal_uart.h" 339 #endif /* HAL_UART_MODULE_ENABLED */ 340 341 #ifdef HAL_USART_MODULE_ENABLED 342 #include "stm32f1xx_hal_usart.h" 343 #endif /* HAL_USART_MODULE_ENABLED */ 344 345 #ifdef HAL_IRDA_MODULE_ENABLED 346 #include "stm32f1xx_hal_irda.h" 347 #endif /* HAL_IRDA_MODULE_ENABLED */ 348 349 #ifdef HAL_SMARTCARD_MODULE_ENABLED 350 #include "stm32f1xx_hal_smartcard.h" 351 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 352 353 #ifdef HAL_WWDG_MODULE_ENABLED 354 #include "stm32f1xx_hal_wwdg.h" 355 #endif /* HAL_WWDG_MODULE_ENABLED */ 356 357 #ifdef HAL_PCD_MODULE_ENABLED 358 #include "stm32f1xx_hal_pcd.h" 359 #endif /* HAL_PCD_MODULE_ENABLED */ 360 361 #ifdef HAL_HCD_MODULE_ENABLED 362 #include "stm32f1xx_hal_hcd.h" 363 #endif /* HAL_HCD_MODULE_ENABLED */ 364 365 #ifdef HAL_MMC_MODULE_ENABLED 366 #include "stm32f1xx_hal_mmc.h" 367 #endif /* HAL_MMC_MODULE_ENABLED */ 368 369 /* Exported macro ------------------------------------------------------------*/ 370 #ifdef USE_FULL_ASSERT 371 /** 372 * @brief The assert_param macro is used for function's parameters check. 373 * @param expr If expr is false, it calls assert_failed function 374 * which reports the name of the source file and the source 375 * line number of the call that failed. 376 * If expr is true, it returns no value. 377 * @retval None 378 */ 379 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 380 /* Exported functions ------------------------------------------------------- */ 381 void assert_failed(uint8_t* file, uint32_t line); 382 #else 383 #define assert_param(expr) ((void)0U) 384 #endif /* USE_FULL_ASSERT */ 385 386 #ifdef __cplusplus 387 } 388 #endif 389 390 #endif /* __STM32F1xx_HAL_CONF_H */ 391
